What Is the Arctic Spas Mylovac™ Cover? The Hot Tub Cover Built for Minnesota Winters

Your hot tub cover works harder than any other part of the spa. It sits outside every day of the year, holds in the heat you pay for, and carries whatever winter piles on top of it. A cover that soaks up water or sags will raise your energy bill and wear out in a few seasons. Arctic Spas® builds its own cover to avoid exactly that. It's called the Mylovac™ cover.

Quick Answer: What Is the Mylovac™ Cover?

Mylovac™ is Arctic's hot tub cover, built around a vacuum-sealed core of double-density foam reinforced with a metal "C" channel. The vacuum seal keeps moisture out of the foam, so the cover stays light and keeps insulating for years. The metal channel lets it support up to 2,000 pounds, so heavy snow won't make it sag.

It comes standard on every Custom Series spa and on every Classic Series spa purchased from Premier Pool & Spa, with a Canvasback™ fabric skin that is at least 25% lighter than vinyl.

Watch: The Mylovac™ Cover Up Close

Arctic Spas shows the Mylovac cover in this short video.  It features the older vinyl skin, which has since been replaced with a lighter weight and more puncture-resistant Canvas Back material.  The full breakdown follows below.

Video courtesy of Arctic Spas®.

Why Most Hot Tub Covers Wear Out

Every hot tub cover is foam inside a protective skin. How long it lasts comes down to what happens to that foam.

Common Ways a Hot Tub Cover Fails

  • It gets waterlogged. Steam from the spa slowly works its way into the foam. Wet foam insulates poorly, can grow mold, and gets heavy enough that the cover is hard to lift.
  • It sags. Snow, ice, and pooled rain push down on the middle. Once the foam bends, water collects in the low spot and the problem gets worse.
  • It leaks heat at the fold. Covers fold in half, and the seam down the middle isn't insulated by the foam inserts unless the cover has a separate piece to fill it.
  • The skin breaks down. Sun and cold crack and fade the outer skin, and torn seams let water reach the foam.

A worn-out cover costs you twice: higher heating bills while it's failing, and the price of a replacement.

How the Mylovac™ Cover Works

Arctic designed every layer of the cover to stop those problems before they start.

Vacuum-Sealed Core

The foam and metal core are vacuum sealed before they go into the skin. Arctic says this keeps moisture completely off the inserts, so the cover holds its insulating value for decades instead of soaking up water.

Double-Density Foam and a Metal "C" Channel

Dense foam with an interwoven metal channel gives the cover the strength to support up to 2,000 pounds of snow and rain, and resist sagging, mold, and collapse.

Tapered to Shed Water

The cover is 5" thick in the center and tapers to 4" at the edges. The raised center sends rain and melting snow off the sides instead of letting it pool on top.

Sealed Against Heat Loss

An insulated baffle fills the fold, wind flaps hang down the sides, and locking straps hold the cover snug to the spa. Heat stays in the water instead of escaping around the edges.

Arctic Spas Mylovac cover on an 8-foot hot tub
Mylovac™ cover on an 8' spa. Image courtesy of Arctic Spas®.
Arctic Spas Mylovac cover on an All-Weather Pool
Mylovac™ covers on an All-Weather Pool. Image courtesy of Arctic Spas®.

Mylovac™ vs. a Typical Hot Tub Cover

What Matters Typical Hot Tub Cover Arctic Spas Mylovac™ Cover
Keeping water out of the foam Foam wrapped in plastic; steam can work its way in over time Vacuum-sealed core built to keep moisture off the inserts
Thickness Many replacement covers taper from 4" to 2" at the edges 5" in the center, tapering to 4"
Snow load Varies by brand; foam alone can sag under heavy, wet snow Double-density foam with a metal "C" channel; supports up to 2,000 pounds
The fold Seam down the middle may not be insulated Insulated baffle fills the fold
Outer skin Usually vinyl Canvasback™ fabric with a water-resistant finish, at least 25% lighter than vinyl

Typical designs are based on published product information from hot tub and replacement cover manufacturers, checked November 2026. Construction differs by brand and model, so confirm the details for the exact spa you're considering.

Why It Matters in Minnesota

Built for Heavy, Wet Snow

A March snowstorm can leave a foot of heavy snow on your spa overnight. The metal-reinforced core is built to carry it without bending, so the cover keeps its shape and keeps shedding water season after season.

Lower Heating Bills All Winter

Most of a hot tub's heat escapes through the top. A dry, well-sealed cover keeps that heat in the water, so the heater runs less. It works together with Arctic's insulated cabinet walls and floor as part of the FreeHeat™ insulation system.

Holds Up Through Freeze-Thaw Cycles

Swings above and below freezing are hard on any outdoor material. Arctic uses UV-resistant materials and heavy-duty seams so the skin doesn't crack, fade, or tear open and let water reach the foam.

Easier to Open Every Day

The Canvasback™ skin is at least 25% lighter than vinyl, so the cover is easier to lift. 

Lock it when you walk away. The Mylovac cover is heavy and locks down with straps, which helps keep children and pets out of the water. Keep it strapped and locked whenever the spa isn't in use.

Which Arctic Spas Come With the Mylovac™ Cover?

  • Custom Series: Included as standard.
  • Classic Series: Included as standard on every Classic spa purchased from Premier Pool & Spa.

Already own an Arctic spa? Replacement cover skins and full covers are available for most models.

Shopping for a Spa? Ask Every Dealer These Questions

Whatever brand you're considering, these questions will tell you how long the cover is likely to last:

  1. How is the foam sealed? What keeps steam and water out of it?
  2. How thick is the cover, and how much does it taper?
  3. Is it reinforced? How much snow can it carry?
  4. Is the fold insulated? Or does heat escape down the middle?
  5. What's the skin made of, and how heavy is the cover to lift?
  6. What does a replacement cover cost, and how often will I need one?

Frequently Asked Questions

How much weight can the cover hold?

Arctic rates the Mylovac cover's metal-reinforced core to support up to 2,000 pounds, so it's built to carry heavy Minnesota snow without sagging.

Is "Mylovac" the vinyl cover?

No. You may hear it used that way, but Mylovac is the vacuum-sealed core inside every Arctic cover. Today it's paired with a Canvasback™ fabric skin.

How do I know if my cover needs replacing?

If it's noticeably heavier than it used to be, sags in the middle, or you can feel heat escaping, the foam has likely taken on water. We can help you check.

Can I replace just the outer skin?

Yes, if the core is still dry and solid. A replacement skin is the outer shell only. If the core is heavy or waterlogged, replace the whole cover. Send us your spa model and serial number and we'll confirm the right part.

Do I need a cover lifter?

It's not required, but it makes opening and closing the cover a one-person job and takes strain off the cover itself. New spas are always priced with a cover lifter. Ask us which lifter fits your spa.

Can I see the Mylovac™ cover in person?

Yes. We have Arctic Spas on display in our Chanhassen showroom, and you're welcome to open and close the cover yourself.

See the Mylovac™ Cover in Person in Chanhassen

Premier Pool & Spa is the Twin Cities' Arctic Spas showroom. Come see the lineup, lift a Mylovac cover yourself, and talk through which model fits your yard and your winter.

Premier Pool & Spa
2985 Water Tower Place
Chanhassen, MN 55317
Call or text: 952-368-6070

Images and video courtesy of Arctic Spas®. Mylovac™, Canvasback™, FreeHeat™, and Arctic Spas® are trademarks of Blue Falls Manufacturing.